Bars & Rods in Carbon Steel, Stainless & Other Metals

1. Bars And Rods In Carbon Steel

We are one of the most prominent Supplier and Exporter of Carbon Steel Round Bar, Carbon Steel Bars, Carbon Steel Round Bar.

Bars And Rods In Carbon Steel

Bars And Rods In Carbon Steel

2. Flat Bar

Flat surfaces, square edges and a variety of thicknesses make the flat bar a versatile steel product with many applications.

With a multitude of uses, such as fencing and gates, furniture work, brackets, benches, shelves and frameworks, the flat bar is used in many fabrication projects.

Flat Bar

Flat Bar

3. Msbar Rod

We are one of the most prominent Suppliers and Exporter of Msbar Rod.

MsBar Rod

MsBar Rod

 

Gaskets API Ring Joint, Spiral Wound, Sheets, Rubber Seal Mech Seals, “O” Rings

1. Gaskets API Ring Joint

Our API Ring Joint Gaskets are used in applications up to 10,000 psi. Oval cross-section gaskets are still a very effective gasket solution where the application requires sealing on existing flanges with round bottom grooves.

Dimensions for API ring joint gaskets and grooves are covered in ANSI B16.20 and API6A.

Gaskets API Ring Joint

Gaskets API Ring Joint

2. Spiral Wound

Spiral Wound Gaskets. Composed of a steel centering (outer) ring, a spiral wound sealing strip (filler) and an inner ring made of special steel, spiral wound gaskets are created by winding alternating strips of metal and filler material.

Spiral Wound

Spiral Wound

 

3. Sheets

Gaskets are normally made from a flat material, a sheet such as paper, rubber, silicone, metal, cork, felt, neoprene, nitrile rubber, fiberglass, polytetrafluoroethylene (otherwise known as PTFE or Teflon) or a plastic polymer (such as polychlorotrifluoroethylene).

Gaskets Sheets

Gaskets Sheets

4. Rubber Seal Mech Seals

A mechanical seal is a device that helps join systems or mechanisms together by preventing leakage (e.g. in a plumbing system), containing pressure, or excluding contamination.

The effectiveness of a seal is dependent on adhesion in the case of sealants and compression in the case of gaskets.

Rubber Seal Mechanicals

Rubber Seal Mechanicals

5. O Rings

An O-ring is a donut, or torus shaped seal typically used to prevent the passing of air or fluid. In other words, Orings are used to keep fluid or air IN or OUT of a defined space

O-Rings

O-Rings

 

Pipe Fitting Equipments: Flanges, Weld neck, Slip-On, Long Neck, Anchor Type In Carbon, Stainless And Alloy Steel

Here is the list of Pipe Fitting Equipments:

1. Flanges

A flange is a method of connecting pipes, valves, pumps and other equipment to form a piping system. It also provides easy access for cleaning, inspection or modification.

Flanges are usually welded or screwed. Flanged joints are made by bolting together two flanges with a gasket between them to provide a seal.

Flange

Flange

2. Weld’s neck

Weld Neck pipe flanges are commonly produced and stocked in several different materials. They are often referred to as Butt Weld Flanges.

When joining these to pipe, the “neck” is butted up to the pipe and welded, similar to welding two pieces of pipe together.

Weld Neck

Weld Neck

 

3. Slip-on

Slip-On Pipe Flanges. They’re manufactured with an inside diameter that is slightly bigger than the pipe’s outside diameter.

These attachments are connected to the pipe via fillet weld at the top and bottom of the flange. Slip-on pipe flanges are typically provided with a raised or flat face.

Slip-on

Slip-On

4. Long Neck

The long neck guides the pipe into the flange itself and provides reinforcement that a standard weld neck flange cannot.

Long weld-neck flanges also are used in situations expansion bends or changes the pipe because of the high pressure.

long-neck

long-neck

5. Anchor Type In Carbon

A wide variety of carbon anchor options are available to you, such as wall anchor, concrete anchor.

Anchor Type In Carbon

Anchor Type In Carbon

6. Anchor Type In Stainless Steel

STAINLESS STEEL ANCHORS: In stone masonry, many metals can cause staining, so austenitic chromium-nickel (18-8) stainless steel (ASTM A167, Type 304) is most commonly used.
stainless steel anchor

Stainless Steel Anchor

7. Anchor Type In Alloy Steel

A wide variety of Alloy steel anchor options are available to you.

Alloy Steel Anchor

Alloy Steel Anchor

 

Pipe fittings; Elbows, Tees, Reduccers, Caps, Weldolets in Carbon, Stainless & Alloy steel

Pipe Fittings are Piping component that helps in Changes the direction of the flow such as elbows, tees. Changes the size of the pipe such as reducers, reducing tees. Large diameter welded fittings are manufactured from the plate.

1. Elbows

The elbow is a pipe fitting installed between two lengths of pipe or tubing to allow a change of direction.

Elbows

Elbows

2. Tees

A pipe tee is used for distributing or collecting the fluid from the run pipe. It is a short piece of pipe with a 90-degree branch at the center.

Pipe Tees

Pipe Tees

3. Reducers

Reducer fittings used by inlet pipework are divided into two types—concentric and eccentric reducers.

Concentric reducer—The reduction of the pipe size is achieved by decreasing the diameter of the fitting at a constant rate over a specified length, maintaining symmetry around the fitting.

Pipe Fitting Reducers

Pipe Fitting Reducers

4. Caps

Pipe caps act as a protective device and are designed to protect the pipe ends of various shapes. The main purpose of using pipe caps is to waterproof the connections.

pipe cap

pipe cap

5. Weldolets in Carbon

Weldolets are used to create a 90-degrees (reinforced) pipe branch. The shape of the Weldolet ensures little stress concentration on the branched pipe, providing an integral reinforcement.

Weldolets in Carbon

Weldolets in Carbon

6. Stainless & Alloy steel

Steels are alloys which are made mainly of iron and carbon, which have high tensile strength and durability. Let us look at the properties of both these steel types.

Properties of Stainless Steel. The main difference between carbon steel and stainless steel is the amount of chromium that is added to the alloy.

Stainless steel

Stainless steel

Alloy Steel

Alloy Steel

Line Pipe; seamless & welded in both carbon steel and stainless steel

Enerquip Pvt Ltd can supply you the best Line Pipe (“seamless & welded in both Carbon steel and stainless steel“).

If you are looking for Line Pipes then you have come to the right place. Because we are 1 stop shop for all your industrial needs.

1. Line Pipe Seamless

Seamless pipe, as the name suggests, is a pipe without a seam or a weld-joint.

Line Pipe Seamless

Line Pipe Seamless

 2. Line Pipe Welded

Welded Pipe is formed by moving the cut coil through a series of rollers, and the seam of the tube is then welded in a chemically neutral environment. 
Welded pipes are typically more cost-effective than their seamless equivalents. Welded pipes are usually more readily available than seamless.
Line Pipe Welded

Line Pipe Welded

 

Steel Structure Materials

Enerquip Pvt Ltd is the best supplier of Steel Structure Materials. If you are looking for Steel Structure Materials then you have come to the right place. Because we are 1 stop shop for all your industrial needs.

Below are the main categories of (“Steel Structure Material”)

1. Angle Iron

Angle Iron is a piece of structural iron or steel in the form of an angle; esp., such a piece in a right angle, used for joining or reinforcing two beams, girders, etc.

Angle Iron

Angle Iron

2. H-Beam

H-Beam is a rolled steel joist or girder with a cross section in the form of a capital letter H. Compare I-beam.

 

H-Beam,

H-Beam

3. C Channel

C Channel structural channel, also known as a Cchannel or Parallel Flange Channel (PFC), is a type of (usually structural steel) beam, used primarily in building construction and civil engineering.

C Channel

C Channel

4. Ms Sheets

Ms sheets are available in any size and thickness as per requirements. CR Sheets are mostly used in automotive industries, electrical goods, panel applications and office equipment and furniture.

MS Sheets

MS Sheets

PPE’s